Product test procedures Technical Support Software This is the technical support software of the product MP TH; with this software you will be able to test all your printer functions. This manual is intended only for technicians trained by Bematech. Chapter 4 – less time to replace the paper roll and, therefore, more time available for processing transactions at the retail outlet. Click on the button ‘Start’ to make a complete test of the printer. Tab ‘additional Commands Tab ‘Additional Commands’ 1. Page 21 – Exploded view of the Control Board Cartr

Uploader: Mikagrel
Date Added: 9 November 2009
File Size: 32.97 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 80644
Price: Free* [*Free Regsitration Required]

Use a soft bristle brush removing all paper dust residues which can accumulate in the cutter mechanism, causing malfunction.

Bematech Printer MP4000 TH User software

To remove mp-40000 cutter sensor located at the front of the mechanism pull it to the front while opening bematfch locks that hold the mechanism picture below, on the left. Exploded View Of The Cover Lever Set The following part numbers are not necessarily available as stand alone units, as they are part of a replacement kit. Execute the steps as required on the screen. Page 32 To remove the paper guide, just press it by its base, disconnecting it from the metal chassis as shown on the picture on the right.

You can change the time the buzzer will be on and the time it will be off.

When the chassis assemble is performed, leave the gears and its pins on the same position, bemateech with bematefh pins pointing out pictures below.

In this field it is possible to choose an image to be printed in the MP TH. By pressing ‘print’ button you will print only current page. Chapter 4 – less time to replace the paper roll and, therefore, more time available for processing transactions at the retail outlet.

Is the sensor placed properly?

Bematech Mp-4000 Th Fi SM SP Thermal POS Receipt USB Printer

Wrong command sequence Verify bematechh the printer command set is properly configured. Click on the ‘Load’ button, on the ‘Update firmware’ field. Tab ‘Macro’ The tab ‘Macro’ allows tests to be processed in batch mode. After fh the plastic chassis, just pull up the back side to loosen the frontal part. The product firmware update can be performed by using the ‘User’s Software’ or the ‘Technical Support Software’.

Page of 55 Go. Only by separating the two chassis it is possible to have access to the thermal print head. The option Bitmap allows you to check the graphics printing and the Logo option allows you to test the functions of logo storage and logo printing from volatile and non volatile memories.

On the window that was open select the firmware that will be loaded and click on open. Introduction This manual provides information on the identification and troubleshooting, test procedures and a list of replacement parts for the MP TH printer. Begin disassembly by removing the control board bemqtech, according to the previous topic.

Bematech MP TH Free Driver Download (Official) () – BemaSetup_MP4K_vzip

Table Of Contents Summary Introduction The communication cable may Verify the cable in all its length to be sure that it be damaged or not properly has no indication of physical damage. Product test procedures Technical Support Software This is the technical support software of the product MP TH; with this software you will be able to test all your printer functions.

Tab ‘Additional Commands’ 1.

When pulling it back, the control board is disconnected from the connection board, located on the frontal portion of the printer. Page 25 – Exploded view of the Cutter Mechanism Se On this field it is possible to tth some changes in the bar code that will be printed.

Before turning on the MP TH, make sure that all cables are properly connected; 3. Page 48 – Verify if the mechanism plastic chassis pins where the sensor is connected image on the side are not broken, which would let the sensor out of its position, leading to its malfunction. Preventive Maintenance Procedures Clean the area near the cutter periodically.

Replace the control board to address the issue.

Tab ‘bar Code 1. Tab ‘additional Commands Tab ‘Additional Commands’ 1. Accessories 1 Please contact Bematech to consult the availability of the interfaces and accessories. Don’t have an account?